Everbuild Everflex Weather Mate | Advanced Gap Filler and Adhesive – Clear – 295 ml & Professional Caulk, Sealant, Adhesive Application Gun for Up to C3/310 ml Cartridges

Price: £18.02
(as of Dec 29,2024 16:23:31 UTC –
From the manufacturer

All surfaces must be clean and dust free. All loose or flaking surface coatings should be removed before application. Glass, metal and aluminium should be cleaned with a solvent cleaner prior to application for optimum adhesion.

Cut the tip of the cartridge taking care not to damage the thread. Apply nozzle and cut cleanly at an angle of 45° with an opening slightly larger than the gap to be sealed.

Apply using a standard sealant gun. Best results will be obtained by keeping an even pressure on the gun trigger and keeping the gun at a constant angle to the surface being sealed.

Always tool down immediately following application using a sealant tool down equipment. When applying to wet surfaces tooling down is essential to ensure a proper bond with the surface is formed. Leave to cure for 24 hours before painting.

Ensure the surface you are applying the sealant/adhesive to is completely clean with no dust. Then cut off the end of the sealant nozzle at a 45 degree angle.

Insert the cartridge into the sealant gun and practise using it on old newspaper. You will want to get the hang of applying the sealant in even quantities. Be careful not to squeeze the trigger too hard or the sealant will shoot out. Be gentle and increase pressure gradually.

Place the nozzle of the tube against the surface of where you want the sealant/adhesive applied and gently squeeze the trigger as you have practised. Holding the gun at a 45 degree angle, move it along the length of the area you want bonded once the sealant starts to come out of the nozzle.

Once you have finished, press the release catch at the back of the sealant gun which will stop all pressure on the tube.

Product 1: For all roofline applications and jointing all types of guttering, filling cracks in stone tiles/slates etc.
Product 1: Adheres to problematic surfaces such as bitumen, asphalt, lead and galvanized steel and general industrial metal panel bonding and gap filling.
Product 1: Perimeter gap filling around window and door frames; ideal for timber frames where woodstaining is required.
Product 1: For all external weatherproofing applications. Can be applied in all weathers, sticks to wet surfaces and for remedial weather proofing over all sealants, putties and mastics.
Product 2: Specifically designed hexagonal rod and reinforced ring for improved strength and durability
Product 2: Features a high compression spring for easy, smooth and controlled application
Product 2: Hook end for simple and safe storage between uses
Product 2: Suitable for use with cartridge caulks, sealants, adhesives and hybrids
)

Reviewer: Ian
Rating: 5.0 out of 5 stars
Title: Good product
Review: Had cracks appearing in the side of my asphalt drive. Used this product to seal the cracks (stop water/ice wrecking the drive).Easy to apply, worked a treat. Wet your finger to smooth,doesn’t stick to your finger. Perfect!It remains quite soft so would not recommend on part of a drive that has heavy traffic.

Reviewer: Walker
Rating: 5.0 out of 5 stars
Title: Excellent product
Review: I initially bought this to seal around a summer house window that was leaking. This product is very fluid and so does penetrate gaps far better than common sealants, as a result it is not the easiest product to shape and leave a clean finish so use masking tape to get neat edges. It is specifically for external use and does have a powerful odour. The sealant takes a while to cure and retains a lot of flexibility once ‘dry’. I have found that this product works particularly well on bitumen surfaces, old and new, and I have used as an adhesive to stick down felt edges that had come unstuck and also to stick felt patches over damaged flat roof areas.

Reviewer: MBTR
Rating: 4.0 out of 5 stars
Title: Everflex Weather Mate Weatherproof and stuck well
Review: I was just about to complain about the ‘expiry’ date. It’s actually the manufacture date and it’s good for two years. The delivery date was 7th June 2021 and it was on time. I haven’t used this purchase but a previously purchased one and it worked perfectly. .

Reviewer: Lulu
Rating: 5.0 out of 5 stars
Title: Great stuff
Review: Perfect for roofs as black and v waterproof lasts for a long time even outside

Reviewer: Dave W
Rating: 5.0 out of 5 stars
Title: Trust the company and sealant
Review: Was unsure about this stuff but at the price I had to give it a go, brilliant and works perfectly as a sealant and adhesive so will buy again. (Had a small issue resolved immediately so great customer service as well), internet business at its best.

Reviewer: hilary
Rating: 5.0 out of 5 stars
Title: Does the job
Review: Easy and quick to use works!

Reviewer: G. Jones
Rating: 4.0 out of 5 stars
Title: Stiky
Review: It is a bit messy I found that it would stick to my tool as I spread it out as I was fixing a licking toilet pipe but once it dried it worked wellAnd dose the job

Reviewer: Stephen Vos
Rating: 3.0 out of 5 stars
Title: Door bell gap fill
Review: Used around doorbell bracket, it wasn’t any better than cheap alternatives I’ve used in the past but is nice and thick, but most annoying is the nozzle didn’t come with a screw top to reseal and use again.

From the manufacturer

All surfaces must be clean and dust free. All loose or flaking surface coatings should be removed before application. Glass, metal and aluminium should be cleaned with a solvent cleaner prior to application for optimum adhesion.

Cut the tip of the cartridge taking care not to damage the thread. Apply nozzle and cut cleanly at an angle of 45° with an opening slightly larger than the gap to be sealed.

Apply using a standard sealant gun. Best results will be obtained by keeping an even pressure on the gun trigger and keeping the gun at a constant angle to the surface being sealed.

Always tool down immediately following application using a sealant tool down equipment. When applying to wet surfaces tooling down is essential to ensure a proper bond with the surface is formed. Leave to cure for 24 hours before painting.

Ensure the surface you are applying the sealant/adhesive to is completely clean with no dust. Then cut off the end of the sealant nozzle at a 45 degree angle.

Insert the cartridge into the sealant gun and practise using it on old newspaper. You will want to get the hang of applying the sealant in even quantities. Be careful not to squeeze the trigger too hard or the sealant will shoot out. Be gentle and increase pressure gradually.

Place the nozzle of the tube against the surface of where you want the sealant/adhesive applied and gently squeeze the trigger as you have practised. Holding the gun at a 45 degree angle, move it along the length of the area you want bonded once the sealant starts to come out of the nozzle.

Once you have finished, press the release catch at the back of the sealant gun which will stop all pressure on the tube.

Product 1: For all roofline applications and jointing all types of guttering, filling cracks in stone tiles/slates etc.
Product 1: Adheres to problematic surfaces such as bitumen, asphalt, lead and galvanized steel and general industrial metal panel bonding and gap filling.
Product 1: Perimeter gap filling around window and door frames; ideal for timber frames where woodstaining is required.
Product 1: For all external weatherproofing applications. Can be applied in all weathers, sticks to wet surfaces and for remedial weather proofing over all sealants, putties and mastics.
Product 2: Specifically designed hexagonal rod and reinforced ring for improved strength and durability
Product 2: Features a high compression spring for easy, smooth and controlled application
Product 2: Hook end for simple and safe storage between uses
Product 2: Suitable for use with cartridge caulks, sealants, adhesives and hybrids