Aidelife Expert Surface Grinding Dust Shroud for Angle Grinder, Universal 5-Inch + Diamond Grinding Cup Wheel AD-1901125D

Price: £32.99
(as of Oct 21,2024 20:51:23 UTC – Aidelife AD-1901125D Surface Grinding Dust Cover is designed to keep the dust in your work area when working with concrete grinding. This unit features a flush sanding door that allows for dust collection for flush sanding. Allows collection of harmful dust while sanding the surface. Application: attaches directly to 4″ / 5″ grinders. Locking attachment on the vacuum cleaner hose. Using this attachment offers improved productivity when using an efficient dust collection system and helps reduce the user’s harmful silica dust. Scope of delivery: 1 x dust cover, 6 x clamp washers thickness 1.5-5.5 mm, 1 x wrench, 1 x universal vacuum cleaner hose adapter, 1 x user manual, 1 x diamond grinding cup.
Aidelife Expert Surface Grinding Dust Shroud for Angle Grinder, Universal 5-Inch + Diamond Grinding Cup Wheel AD-1901125D
Product tpe: DISC GRINDER TOOL
Brand: Aidelife
Color: Red
)

Reviewer: Jason Hanks
Rating: 5.0 out of 5 stars
Title: Excellent
Review: This was an absolute gift..I didn’t use it on my Makita cordless but instead had an old corded extreme brand bought from Argos and it fitted perfectly without any of the adapters needed. I’d quite a large area that needed to be levelled out and connected to my Makita shop vacuum I was actually amazed at how well it worked. Dust was kept to a minimum while holding the grinder parallel to the floor so the brushes on did their job.All in all I would recommend this product as here in Ireland you would struggle just to buy the grinding disc for the price.

Reviewer: Kay carpenter
Rating: 4.0 out of 5 stars
Title: Works well just needs a little modification.
Review: Works well but the vacuum link up accessories could be a better fit…had to duck tape them in place to work properly.

Reviewer: Chrissie
Rating: 5.0 out of 5 stars
Title: It works!
Review: Bought this to grind the thinset down in my kitchen floor. Sadly it did not fit my angle grinder because my angle grinder was too big….. However it did fit my tilers small angle grinder and he was able to get rid of thinset with the minimal amount of dust, made a difficult job easy. It was excellent value for money, decent quality however do check the size of your angle grinder first.

Reviewer: jeep
Rating: 3.0 out of 5 stars
Title: It works but takes a lot of setting up, perhaps washers should be supplied
Review: I used this with my Challenge 600W angle grinder which is about 15 years old now. Was pleased to see the instruction pictures on Amazon that shows you tool fitting tolerances. These checked out with my angle grinder. But I found that I had to do quite a bit of fine tuning to achieve the 1/16″ – 1/8″ mentioned early on in the printed instructions which suggests using washers to get the grinding disc above the level of the brush skirt.I also had to cut some small notches in the clamp collar to get it to sit over the the flange bolts on the end of the tool. The angle grinder drive spindle was only just long enough when adjusted with washers to obtain the correct height, so the life of the grinding disc will be limited as once it starts to wear I won’t be able to add any more packing washers.It worked quite well with my Titan industrial Vac and did the job. So for occasional use not a bad buy, but a bit of a fiddle to set up.

Reviewer: Griffer
Rating: 5.0 out of 5 stars
Title: Surprisingly good but I think the suggestion to use washers to adjust cut depth is dangerous
Review: The grinding cup and shroud were surprisingly effective – no dust at all and just with a Henry hoover, not an industrial vacuum.However, I disagree strongly with the instructions to pack washers behind the grinding cup to adjust the cut height, which is controlled by the relative levels of the bristles and the grinding cup. Unless you have a supply of 22mm ID washers, 14mm ID washers and a 22mmx 14mm washer sufficiently thick to centre the grinding cup on what will probably be a threaded section of the drive shaft, you are going to end up with a grinding cup that is not properly secured and almost certainly out of balance.A far simpler (and safer) solution is to trim the height of the bristles to the required level with a pair of sharp scissors and to keep trimming if the grinding cup shows significant wear – which mine didn’t.Yes, it’s a one-way process, so not ideal if you expect to use it so much that you wear out the grinding cup and have to replace it with a new one, but for the average user with a one-off job it could avoid a trip to A&E.

Reviewer: Voutchko
Rating: 5.0 out of 5 stars
Title: This is actually very good product!
Review: fits bosch 18V grinder

Reviewer: Sebastian Z.
Rating: 1.0 out of 5 stars
Title: Waste of time and money
Review: No good looks very unsafe I try to assemby and have fear to use

Reviewer: Rich
Rating: 2.0 out of 5 stars
Title: Doesn’t fit ryobi
Review: Greta tool but wouldn’t fit my ryobi grinder like it said

Aidelife AD-1901125D Surface Grinding Dust Cover is designed to keep the dust in your work area when working with concrete grinding. This unit features a flush sanding door that allows for dust collection for flush sanding. Allows collection of harmful dust while sanding the surface. Application: attaches directly to 4″ / 5″ grinders. Locking attachment on the vacuum cleaner hose. Using this attachment offers improved productivity when using an efficient dust collection system and helps reduce the user’s harmful silica dust. Scope of delivery: 1 x dust cover, 6 x clamp washers thickness 1.5-5.5 mm, 1 x wrench, 1 x universal vacuum cleaner hose adapter, 1 x user manual, 1 x diamond grinding cup.
Aidelife Expert Surface Grinding Dust Shroud for Angle Grinder, Universal 5-Inch + Diamond Grinding Cup Wheel AD-1901125D
Product tpe: DISC GRINDER TOOL
Brand: Aidelife
Color: Red